Raritan PX-1000 Series User's Guide Page 22
- Page / 258
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
This chapter explains how to install a Dominion PX device and configure it
for network connectivity.
In This Chapter
Before You Begin ....................................................................................10
Installing Cable Retention Clips (Optional)
..............................................12
Connecting the PDU to a Power Source.................................................13
Configuring Dominion PX........................................................................13
Connecting E
nvironmental Sensors (Optional
).......................................20
Connecting the Asset Management Sensor (Optional)
...........................25
Before You Begin
Before beginning the installation, perform the following activities:
Unpack the product and components
Prepare the installation site
Fill out the equipment setup worksheet
Unpacking the Product and Components
1. Remove the Dominion PX device and other equipment from the box in
which they were shipped. See Package Contents (on page 2) for a
comp
lete list of the contents of the box.
2. Compare the serial number of the equipment with the number on the
packing slip located on the outside of the box and make sure they
match.
3. Inspect the equipment carefully. If any of the equipment is damaged or
missing, contact Raritan's Technical Support Department for
assistance.
4. Verify that all circuit breakers on the Dominion PX device are set to
ON. If not, turn them ON.
For a PDU with fuses, ensure that all fuses are inserted and seated
properly. If there are any fuse covers, ensure that they are closed.
Note: Not all Dominion PX devices have overcurrent protection
mechanisms.
Preparing the Installation Site
1. Make sure the installation area is clean and free of extreme
temperatures and humidity.
Chapter 3
Installation and Configuration
- PX-1000 Series 1
- Safety Guidelines 2
- Safety Instructions 3
- FCC Information 4
- VCCI Information (Japan) 4
- Contents 7
- Contents 10
- Applicable Models 11
- Chapter 1 13
- Introduction 13
- Package Contents 14
- Chapter 1: Introduction 15
- Chapter 2 16
- Rack-Mounting the PDU 16
- Mounting 1U or 2U Models 19
- Chapter 3 22
- Configuring Dominion PX 25
- Contact Closure Sensor LEDs 36
- Chapter 4 40
- Using the PDU 40
- Chapter 4: Using the PDU 41
- Chapter 4: Using the PDU 42
- Three-Digit Row 43
- Two-Digit Row 44
- LEDs for Measurement Units 44
- Automatic Mode 45
- Manual Mode 45
- Circuit Breakers 46
- Chapter 5 49
- Using the Web Interface 49
- Expanding the Tree 55
- Collapsing the Tree 56
- Adjusting the Pane 56
- Warning Icon 59
- Changing the View of a List 60
- Changing the Column 60
- Changing the Sorting 61
- Resizing a Dialog 61
- Viewing the Dashboard 63
- Device Management 63
- Role of a DNS Server 67
- Wired Network Settings 67
- Wireless Network Settings 68
- Changing the SSH Settings 69
- Changing the Telnet Settings 70
- How to Use the Calendar 73
- Enabling Data Logging 74
- User Management 76
- Setting Up Roles 80
- Access Security Control 84
- Enabling the Firewall 85
- Changing the Default Policy 85
- Creating Firewall Rules 86
- Editing Firewall Rules 88
- Sorting Firewall Rules 88
- Deleting Firewall Rules 88
- Enabling User Blocking 89
- Enabling Login Limitations 90
- Enabling Strong Passwords 90
- Enabling Password Aging 91
- Enabling the Feature 92
- Outlet Management 105
- Setting Power Thresholds 110
- Configuring Event Rules 114
- Creating Actions 115
- Creating Rules 116
- Sample PDU-Level Event Rule 118
- Managing Event Logging 122
- Viewing Connected Users 123
- Environmental Sensors 125
- Sensor Measurement Accuracy 131
- States of Managed Sensors 131
- "normal" State 132
- "alarmed" State 133
- Asset Management 134
- Network Diagnostics 140
- Firmware Upgrade 143
- Using SNMP 144
- Accessing the Help 145
- Chapter 6 148
- Downloading 149
- SNMP MIB 149
- Configuring SNMP Traps 150
- SNMP Gets and Sets 151
- Chapter 6: Using SNMP 152
- SNMP Sets and Thresholds 153
- Chapter 7 154
- Help Command 157
- Showing Information 158
- Changing the PDU Name 171
- Example 171
- Setting the Networking Mode 173
- Setting the SSID 174
- Setting the PSK 174
- Setting the BSSID 175
- Changing the LAN Duplex Mode 176
- Setting the IP Address 177
- Setting the Subnet Mask 178
- Setting the Gateway 178
- Changing the HTTP Port 180
- Changing the HTTPS Port 181
- IP Access Control 181
- HTTPS Access 184
- Login Limitation 185
- User Blocking 186
- Strong Passwords 187
- Changing the Outlet Name 190
- Changing the Inlet Name 190
- Changing the Sensor Name 191
- Setting the X Coordinate 192
- Setting the Y Coordinate 192
- Setting the Z Coordinate 193
- Commands for Inlet Sensors 194
- Creating a User Profile 216
- Modifying a User Profile 217
- Deleting a User Profile 222
- Changing Your Own Password 223
- Creating a Role 223
- Modifying a Role 224
- Deleting a Role 226
- Unblocking a User 228
- Resetting Dominion PX 228
- Network Troubleshooting 229
- Retrieving Previous Commands 232
- Logging out of CLI 233
- Appendix A 234
- Specifications 234
- Appendix B 236
- Equipment Setup Worksheet 236
- Appendix C 240
- MAC Address 240
- Appendix D 241
- Appendix E 249
- Using the CLI Command 250
- Appendix F 252
- Attached 252
- Index 255
© 2020, manymanuals.com. All rights reserved. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals